Discovering Plumbing Basics is Crucial for Installing a Bathtub
Discovering Plumbing Basics is Crucial for Installing a Bathtub
Blog Article
How do you feel with regards to A Step-by-Step Guide to Installing a Bathtub?
Installing a tub isn't exactly rocket science, however it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably difficult project. If the old bathtub is conveniently obtainable, the task can relocate easily; if you have to open a wall to get rid of the old tub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need an assistant to move out the old tub as well as set in the brand-new one. See to it you have certified yourself for the work as well as are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is better to think about utilizing one before you begin. Chances are you might need a professional plumber to make tube links.
This write-up will certainly aid you install a brand-new bath tub in your washroom if you have already acquired a new bathtub and also don't require to change the arrangement of your previous water supply pipes.
Your devices and also material checklist need to comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted access that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth prepared for the staying water that will come from the pipes. Once the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making sure that the washers are in area between the faucet as well as the sink. Safeguard the tap in position with the maker given backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal tap ports. The former kind must be attached to the faucet finishes first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the called for setting. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub up until the level checks out level.
To mount faucets, fit all-time low of the outermost versatile faucet connector to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if required. Load the tub and also inspect the overflow outlet as well as the typical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub should wait till the bath tub has been made use of at the very least once as this will resolve it into its last position.
Planning for the Installment
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets device to avoid pressure on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall surface between the bathroom as well as the tiling, resulting in issues with wetness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes as well as cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Remember to always fill up the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can fracture rather very early if you do not think about this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed our topic about A Step-by-Step Guide to Installing a Bathtub. Thank you so much for spending some time to browse our piece. Be sure to set aside a second to distribute this blog post if you enjoyed reading it. Thank you so much for taking the time to read it.
Schedule Report this page